[ previous ] [ next ] [ threads ]
 To :  Raj Roy Ghandhi <roy.gandhi@g...>
 From :  Bohumil Tosovsky <bohumil.tosovsky@g...>
 Subject :  Re: [yate] Re: sccp.message - decode hexData param value
 Date :  Wed, 21 Jan 2015 13:31:03 +0100
If i remember correctly, try to enable printing messages on the gtt. Do you
have also enabled sniffing ?



2015-01-21 11:34 GMT+01:00 Raj Roy Ghandhi :

> Hi Bohumil,
> Thanks for the mail.
> Please find the ysigchan.conf below.
>
> [general]
> debuglevel=8,8,8,8,8
> ;debuglevel_engine=
> ;dtmfinband=no
> ;floodevents=20
> ;maxlock=10000 normally, -1 if Yate is started with -Dm
> ;datafile=
> ; Each section except [general] can have some common parameters
> ;enable=yes
> ;debugname=
> ;debuglevel=
>
>
>
> [linkset1]
> type=ss7-mtp3
> netind2pctype=ITU
> netindicator=national
> ;route=ITU,5-5-0
> adjacent=ITU,5-5-0
> local=ITU,5-5-3
> ;allowed=
> router=ss7router
> link=link1
> slcshift=false
> autostart=yes
> checklinks=true
> forcealign=true
> checkfails=5000
> maintenance=60000
> ;layer3dump=
>
>
> [link1]
> type=ss7-m2pa
> autostart=yes
> emergency=yes
> autoemergency=yes
> sig=sig111
> filllink=yes
> maxerrors=64
> rxunderrun=0
> layer2dump=
>
>
>
> ;[ss7router]
> ;type=ss7-router
> ;transfer=no
> ; Example: local=ITU,2-2-4
> ;local=
> ;management=ss7snm
> ;starttime=
> ;isolation=1000
> ;autostart=no
> ;autoallow=no
> ;sendupu=yes
> ;sendtfp=yes
> ; testroutes=50000
> ;testrestricted=no
>
>
> ;[ss7snm]
> ;type=ss7-snm
> ; Example: local=ITU,2-2-4
> ;local=
> ;priority=regular
> ;netindicator=national
> ;changemsgs=yes
> ;changesets=no
> ;neighbours=yes
>
>
> [sccp]
> type=ss7-sccp
> pointcodetype=ITU
> localpointcode=5-5-3
> router=ss7router
> ;network=
> management=sccp-mgm
> hopcounter=15
> ludt-support=false
> segmentation-timeout=5000
> extended-monitoring=true
> print-messages=true
> extended-debug=true
> endpoint=true
>
>
> ;[sccp-mgm]
> ;type=ss7-sccp-itu-mgm
> ;test-timer=5000
> ;print-messages=false
> ;remote=2057:1,2,3,4
> ;concerned=2057:1,2,3,4
> ;local-subsystems=1,2,3,4,5,..
> ;auto-monitor=false
>
>
> [gtt]
> type=ss7-gtt
> sccp=sccp
>
>
> ;[sccp-userd]
> ;type=ss7-sccpu-dummy
> ;sccp=sccp
> ;ssn=0
>
>
>
> [hlr]
> type=ss7-tcap-itu
> local_SSN=6
> default_remote_SSN=8
> default_remote_pointcode=5-5-3
> pointcodetype=ITU
> sccp=sccp
> default_hopcounter=false
> transact_timeout=300
> print-messages=true
> extended-debug=true
>
> ;[smsc]
> ;type=ss7-tcap-itu
> ;local_SSN=147
> ;default_remote_SSN=8
> ;default_remote_pointcode=5-5-3
> ;pointcodetype=ITU
> ;sccp=sccp
> ;default_hopcounter=false
> ;transact_timeout=300
> ;print-messages=true
> ;extended-debug=true
>
>
> ;[tcapuser_test]
> ;type=ss7-tcap-user
> ;tcap=
>
> Best Regards,
> Roy.
>
>
> On Wed, Jan 21, 2015 at 3:59 PM, Bohumil Tosovsky <
> bohumil.tosovsky@g...> wrote:
>
>>
>>
>>
>> SCCP GTT is working, you must have configured sccp layer properly. Can
>> you send your ysigchan.conf?
>>
>> 2015-01-21 8:52 GMT+01:00 Raj Roy Ghandhi :
>>
>>> Hi Friends,
>>> Is there anyone who has done this ?
>>>
>>> Best Regards,
>>> Roy.
>>>
>>> On Tue, Jan 20, 2015 at 12:01 AM, Raj Roy Ghandhi 
>>> wrote:
>>>
>>>> Hi Friends,
>>>> Is there a easy way to decode the  param['hexData']  in sccp.message
>>>> and fetch the values in messaging level.
>>>>
>>>> param['hexData'] = '62 47 48 04 00 00 01 64 6b 1e 28 1c 06 07 00 11 86
>>>> 05 01 01 01 a0 11 60 0f 80 02 07 80 a1 09 06 07 04 00 00 01 00 05 03 6c 1f
>>>> a1 1d 02 01 01 02 01 16 30 15 80 07 81 49 97 28 22 33 f3 83 01 00 86 07 91
>>>> 49 97 10 00 01 f1'
>>>>
>>>> I do no want to modify the camel_map.cpp
>>>>
>>>> Please advice.
>>>>
>>>> Best Regards,
>>>> Roy.
>>>>
>>>
>>>
>>
>>
>



If i remember correctly, try to enable printing messages on the gtt. Do you have also enabled sniffing ?



2015-01-21 11:34 GMT+01:00 Raj Roy Ghandhi <roy.gandhi@g...>:
Hi Bohumil,
Thanks for the mail.
Please find the ysigchan.conf below.

[general]
debuglevel=8,8,8,8,8
;debuglevel_engine=
;dtmfinband=no
;floodevents=20
;maxlock=10000 normally, -1 if Yate is started with -Dm
;datafile=
; Each section except [general] can have some common parameters
;enable=yes
;debugname=
;debuglevel=



[linkset1]
type=ss7-mtp3
netind2pctype=ITU
netindicator=national
;route=ITU,5-5-0
adjacent=ITU,5-5-0
local=ITU,5-5-3
;allowed=
router=ss7router
link=link1
slcshift=false
autostart=yes
checklinks=true
forcealign=true
checkfails=5000
maintenance=60000
;layer3dump=


[link1]
type=ss7-m2pa
autostart=yes
emergency=yes
autoemergency=yes
sig=sig111
filllink=yes
maxerrors=64
rxunderrun=0
layer2dump=



;[ss7router]
;type=ss7-router
;transfer=no
; Example: local=ITU,2-2-4
;local=
;management=ss7snm
;starttime=
;isolation=1000
;autostart=no
;autoallow=no
;sendupu=yes
;sendtfp=yes
; testroutes=50000
;testrestricted=no


;[ss7snm]
;type=ss7-snm
; Example: local=ITU,2-2-4
;local=
;priority=regular
;netindicator=national
;changemsgs=yes
;changesets=no
;neighbours=yes


[sccp]
type=ss7-sccp
pointcodetype=ITU
localpointcode=5-5-3
router=ss7router
;network=
management=sccp-mgm
hopcounter=15
ludt-support=false
segmentation-timeout=5000
extended-monitoring=true
print-messages=true
extended-debug=true
endpoint=true


;[sccp-mgm]
;type=ss7-sccp-itu-mgm
;test-timer=5000
;print-messages=false
;remote=2057:1,2,3,4
;concerned=2057:1,2,3,4
;local-subsystems=1,2,3,4,5,..
;auto-monitor=false


[gtt]
type=ss7-gtt
sccp=sccp


;[sccp-userd]
;type=ss7-sccpu-dummy
;sccp=sccp
;ssn=0



[hlr]
type=ss7-tcap-itu
local_SSN=6
default_remote_SSN=8
default_remote_pointcode=5-5-3
pointcodetype=ITU
sccp=sccp
default_hopcounter=false
transact_timeout=300
print-messages=true
extended-debug=true

;[smsc]
;type=ss7-tcap-itu
;local_SSN=147
;default_remote_SSN=8
;default_remote_pointcode=5-5-3
;pointcodetype=ITU
;sccp=sccp
;default_hopcounter=false
;transact_timeout=300
;print-messages=true
;extended-debug=true


;[tcapuser_test]
;type=ss7-tcap-user
;tcap=

Best Regards,
Roy.


On Wed, Jan 21, 2015 at 3:59 PM, Bohumil Tosovsky <bohumil.tosovsky@g...> wrote:



SCCP GTT is working, you must have configured sccp layer properly. Can you send your ysigchan.conf?

2015-01-21 8:52 GMT+01:00 Raj Roy Ghandhi <roy.gandhi@g...>:
Hi Friends,
Is there anyone who has done this ?

Best Regards,
Roy.

On Tue, Jan 20, 2015 at 12:01 AM, Raj Roy Ghandhi <roy.gandhi@g...> wrote:
Hi Friends,
Is there a easy way to decode the  param['hexData']  in sccp.message and fetch the values in messaging level.

param['hexData'] = '62 47 48 04 00 00 01 64 6b 1e 28 1c 06 07 00 11 86 05 01 01 01 a0 11 60 0f 80 02 07 80 a1 09 06 07 04 00 00 01 00 05 03 6c 1f a1 1d 02 01 01 02 01 16 30 15 80 07 81 49 97 28 22 33 f3 83 01 00 86 07 91 49 97 10 00 01 f1'

I do no want to modify the camel_map.cpp

Please advice.

Best Regards,
Roy.