[ previous ] [ next ] [ threads ]
 To :  Bohumil Tosovsky <bohumil.tosovsky@g...>
 From :  Raj Roy Ghandhi <roy.gandhi@g...>
 Subject :  Re: [yate] Re: sccp.message - decode hexData param value
 Date :  Thu, 22 Jan 2015 09:46:48 +0530
Yes. I can see the message when the sniffer is on in yate.conf



On Wed, Jan 21, 2015 at 6:01 PM, Bohumil Tosovsky <
bohumil.tosovsky@g...> wrote:

> If i remember correctly, try to enable printing messages on the gtt. Do
> you have also enabled sniffing ?
>
>
>
> 2015-01-21 11:34 GMT+01:00 Raj Roy Ghandhi :
>
>> Hi Bohumil,
>> Thanks for the mail.
>> Please find the ysigchan.conf below.
>>
>> [general]
>> debuglevel=8,8,8,8,8
>> ;debuglevel_engine=
>> ;dtmfinband=no
>> ;floodevents=20
>> ;maxlock=10000 normally, -1 if Yate is started with -Dm
>> ;datafile=
>> ; Each section except [general] can have some common parameters
>> ;enable=yes
>> ;debugname=
>> ;debuglevel=
>>
>>
>>
>> [linkset1]
>> type=ss7-mtp3
>> netind2pctype=ITU
>> netindicator=national
>> ;route=ITU,5-5-0
>> adjacent=ITU,5-5-0
>> local=ITU,5-5-3
>> ;allowed=
>> router=ss7router
>> link=link1
>> slcshift=false
>> autostart=yes
>> checklinks=true
>> forcealign=true
>> checkfails=5000
>> maintenance=60000
>> ;layer3dump=
>>
>>
>> [link1]
>> type=ss7-m2pa
>> autostart=yes
>> emergency=yes
>> autoemergency=yes
>> sig=sig111
>> filllink=yes
>> maxerrors=64
>> rxunderrun=0
>> layer2dump=
>>
>>
>>
>> ;[ss7router]
>> ;type=ss7-router
>> ;transfer=no
>> ; Example: local=ITU,2-2-4
>> ;local=
>> ;management=ss7snm
>> ;starttime=
>> ;isolation=1000
>> ;autostart=no
>> ;autoallow=no
>> ;sendupu=yes
>> ;sendtfp=yes
>> ; testroutes=50000
>> ;testrestricted=no
>>
>>
>> ;[ss7snm]
>> ;type=ss7-snm
>> ; Example: local=ITU,2-2-4
>> ;local=
>> ;priority=regular
>> ;netindicator=national
>> ;changemsgs=yes
>> ;changesets=no
>> ;neighbours=yes
>>
>>
>> [sccp]
>> type=ss7-sccp
>> pointcodetype=ITU
>> localpointcode=5-5-3
>> router=ss7router
>> ;network=
>> management=sccp-mgm
>> hopcounter=15
>> ludt-support=false
>> segmentation-timeout=5000
>> extended-monitoring=true
>> print-messages=true
>> extended-debug=true
>> endpoint=true
>>
>>
>> ;[sccp-mgm]
>> ;type=ss7-sccp-itu-mgm
>> ;test-timer=5000
>> ;print-messages=false
>> ;remote=2057:1,2,3,4
>> ;concerned=2057:1,2,3,4
>> ;local-subsystems=1,2,3,4,5,..
>> ;auto-monitor=false
>>
>>
>> [gtt]
>> type=ss7-gtt
>> sccp=sccp
>>
>>
>> ;[sccp-userd]
>> ;type=ss7-sccpu-dummy
>> ;sccp=sccp
>> ;ssn=0
>>
>>
>>
>> [hlr]
>> type=ss7-tcap-itu
>> local_SSN=6
>> default_remote_SSN=8
>> default_remote_pointcode=5-5-3
>> pointcodetype=ITU
>> sccp=sccp
>> default_hopcounter=false
>> transact_timeout=300
>> print-messages=true
>> extended-debug=true
>>
>> ;[smsc]
>> ;type=ss7-tcap-itu
>> ;local_SSN=147
>> ;default_remote_SSN=8
>> ;default_remote_pointcode=5-5-3
>> ;pointcodetype=ITU
>> ;sccp=sccp
>> ;default_hopcounter=false
>> ;transact_timeout=300
>> ;print-messages=true
>> ;extended-debug=true
>>
>>
>> ;[tcapuser_test]
>> ;type=ss7-tcap-user
>> ;tcap=
>>
>> Best Regards,
>> Roy.
>>
>>
>> On Wed, Jan 21, 2015 at 3:59 PM, Bohumil Tosovsky <
>> bohumil.tosovsky@g...> wrote:
>>
>>>
>>>
>>>
>>> SCCP GTT is working, you must have configured sccp layer properly. Can
>>> you send your ysigchan.conf?
>>>
>>> 2015-01-21 8:52 GMT+01:00 Raj Roy Ghandhi :
>>>
>>>> Hi Friends,
>>>> Is there anyone who has done this ?
>>>>
>>>> Best Regards,
>>>> Roy.
>>>>
>>>> On Tue, Jan 20, 2015 at 12:01 AM, Raj Roy Ghandhi >>> > wrote:
>>>>
>>>>> Hi Friends,
>>>>> Is there a easy way to decode the  param['hexData']  in sccp.message
>>>>> and fetch the values in messaging level.
>>>>>
>>>>> param['hexData'] = '62 47 48 04 00 00 01 64 6b 1e 28 1c 06 07 00 11 86
>>>>> 05 01 01 01 a0 11 60 0f 80 02 07 80 a1 09 06 07 04 00 00 01 00 05 03 6c 1f
>>>>> a1 1d 02 01 01 02 01 16 30 15 80 07 81 49 97 28 22 33 f3 83 01 00 86 07 91
>>>>> 49 97 10 00 01 f1'
>>>>>
>>>>> I do no want to modify the camel_map.cpp
>>>>>
>>>>> Please advice.
>>>>>
>>>>> Best Regards,
>>>>> Roy.
>>>>>
>>>>
>>>>
>>>
>>>
>>
>



Yes. I can see the message when the sniffer is on in yate.conf



On Wed, Jan 21, 2015 at 6:01 PM, Bohumil Tosovsky <bohumil.tosovsky@g...> wrote:
If i remember correctly, try to enable printing messages on the gtt. Do you have also enabled sniffing ?



2015-01-21 11:34 GMT+01:00 Raj Roy Ghandhi <roy.gandhi@g...>:
Hi Bohumil,
Thanks for the mail.
Please find the ysigchan.conf below.

[general]
debuglevel=8,8,8,8,8
;debuglevel_engine=
;dtmfinband=no
;floodevents=20
;maxlock=10000 normally, -1 if Yate is started with -Dm
;datafile=
; Each section except [general] can have some common parameters
;enable=yes
;debugname=
;debuglevel=



[linkset1]
type=ss7-mtp3
netind2pctype=ITU
netindicator=national
;route=ITU,5-5-0
adjacent=ITU,5-5-0
local=ITU,5-5-3
;allowed=
router=ss7router
link=link1
slcshift=false
autostart=yes
checklinks=true
forcealign=true
checkfails=5000
maintenance=60000
;layer3dump=


[link1]
type=ss7-m2pa
autostart=yes
emergency=yes
autoemergency=yes
sig=sig111
filllink=yes
maxerrors=64
rxunderrun=0
layer2dump=



;[ss7router]
;type=ss7-router
;transfer=no
; Example: local=ITU,2-2-4
;local=
;management=ss7snm
;starttime=
;isolation=1000
;autostart=no
;autoallow=no
;sendupu=yes
;sendtfp=yes
; testroutes=50000
;testrestricted=no


;[ss7snm]
;type=ss7-snm
; Example: local=ITU,2-2-4
;local=
;priority=regular
;netindicator=national
;changemsgs=yes
;changesets=no
;neighbours=yes


[sccp]
type=ss7-sccp
pointcodetype=ITU
localpointcode=5-5-3
router=ss7router
;network=
management=sccp-mgm
hopcounter=15
ludt-support=false
segmentation-timeout=5000
extended-monitoring=true
print-messages=true
extended-debug=true
endpoint=true


;[sccp-mgm]
;type=ss7-sccp-itu-mgm
;test-timer=5000
;print-messages=false
;remote=2057:1,2,3,4
;concerned=2057:1,2,3,4
;local-subsystems=1,2,3,4,5,..
;auto-monitor=false


[gtt]
type=ss7-gtt
sccp=sccp


;[sccp-userd]
;type=ss7-sccpu-dummy
;sccp=sccp
;ssn=0



[hlr]
type=ss7-tcap-itu
local_SSN=6
default_remote_SSN=8
default_remote_pointcode=5-5-3
pointcodetype=ITU
sccp=sccp
default_hopcounter=false
transact_timeout=300
print-messages=true
extended-debug=true

;[smsc]
;type=ss7-tcap-itu
;local_SSN=147
;default_remote_SSN=8
;default_remote_pointcode=5-5-3
;pointcodetype=ITU
;sccp=sccp
;default_hopcounter=false
;transact_timeout=300
;print-messages=true
;extended-debug=true


;[tcapuser_test]
;type=ss7-tcap-user
;tcap=

Best Regards,
Roy.


On Wed, Jan 21, 2015 at 3:59 PM, Bohumil Tosovsky <bohumil.tosovsky@g...> wrote:



SCCP GTT is working, you must have configured sccp layer properly. Can you send your ysigchan.conf?

2015-01-21 8:52 GMT+01:00 Raj Roy Ghandhi <roy.gandhi@g...>:
Hi Friends,
Is there anyone who has done this ?

Best Regards,
Roy.

On Tue, Jan 20, 2015 at 12:01 AM, Raj Roy Ghandhi <roy.gandhi@g...> wrote:
Hi Friends,
Is there a easy way to decode the  param['hexData']  in sccp.message and fetch the values in messaging level.

param['hexData'] = '62 47 48 04 00 00 01 64 6b 1e 28 1c 06 07 00 11 86 05 01 01 01 a0 11 60 0f 80 02 07 80 a1 09 06 07 04 00 00 01 00 05 03 6c 1f a1 1d 02 01 01 02 01 16 30 15 80 07 81 49 97 28 22 33 f3 83 01 00 86 07 91 49 97 10 00 01 f1'

I do no want to modify the camel_map.cpp

Please advice.

Best Regards,
Roy.